MODEL 250IX

The 250ix Powersports Chassis Dynamometer provides the ultimate in powersports dyno tuning/testing capability. With 61 inch total drum with, and extra drum and sliding carriage, the 250ix can handle UTV's, ATV's, Karts, Trikes, and Motorcycles. Available for above-ground or pit installation.

Above Ground Standard Features and Equipment

  • Accommodates Motorcycles and most other powersports platforms (ATV’s, Side-by-Sides, Go-Karts, and Trikes)
  • Measures 750+ HP / Torque And Up To 200 MPH
  • Eddy Current Load Absorption Unit (250 series only)
  • Powder coated chassis, wheelbase capability up to 84 inches (from rear axle to front tire)
  • PowerCore Software suite with WinPEP 8 (PC, monitor, printer, etc. not included)
  • DynoWare RT dynamometer electronics and hardware
  • Integrated control panel stand with console
  • Ignition wire inductive tachometer pickup leads
  • Front wheel lock
  • 2 channels available for Automatic Conditions Measurement (absolute pressure, air temp, humidity) 1 sensor included
  • 4 Analog Input Channels for 0-5v sensors (sensors and cables not included)
  • 14 expansion ports for DynoWare RT accessories and DJ-CAN devices (such as Power Commander, Power Vision, Autotune, etc.)
  • Starter system to spin roller (12V, battery not included)
  • Installation and operation manuals
  • One year replacement parts warranty
  • Free technical support

Pit Model Standard Features and Equipment

  • Accommodates Motorcycles and most other powersports platforms (ATV’s, Side-by-Sides, Go-Karts, and Trikes)
  • Measures 750+ HP / Torque And Up To 200 MPH
  • Eddy Current Load Absorption Unit (250 series only)
  • PowerCore Software suite with WinPEP 8 (PC, monitor, printer, etc. not included)
  • DynoWare RT dynamometer electronics and hardware
  • 2 channels available for Automatic Conditions Measurement (absolute pressure, air temp, humidity) 1 sensor included
  • 4 Analog Input Channels for 0-5v sensors (sensors and cables not included)
  • 14 expansion ports for DynoWare RT accessories and DJ-CAN devices (such as Power Commander, Power Vision, Autotune, etc.)
  • Integrated control panel stand with console
  • Ignition wire inductive tachometer pickup leads
  • Power carriage for button operated wheelbase adjustment
  • Pit Covers
  • Compact design allows for smaller pit size
  • Front wheel lock
  • Automatic atmospheric conditions measurement (absolute pressure, air temp, humidity)
  • Starter system to spin roller (12V, battery not included)
  • Installation and operation manuals
  • One year replacement parts warranty
  • Free technical support

Dynamometer Specifications Information

Below is a list of the Dynamometer specifications. In addition, you can download a pdf specs. document from below. For additional specifications related questions, please give us a call at: 01995 600500.

  Pre-installation Guide  Download   Standard Carriage Wheelbase Minimum   66 IN / 167 CM
  200i/250i Installation Guide   Download   Standard Carriage Wheelbase Maximum   84 IN / 213 CM             
  200iP/250iP Installation Guide   Download   Extended Carriage Wheelbase Minimum   83 IN / 210 CM*
  Maximum Horsepower / Torque   750 HP / 750 FT LBS   Extended Carriage Wheelbase Maximum   102 IN / 259 CM*
  Maximum Speed   200 MPH / 322 KPH   Air Requirements   100 PSI
  Drum Diameter   18 IN / 45.72 CM   Operating Temp Range   32 to 158 F / 0 to 70 C
  Width   16.37 IN / 41.59 CM   Timing Accuracy   +/-1 Microsecond
  Drums   2   Drum Speed Accuracy   +/-1/100th MPH
  Maximum Axle Weight   N/A   RPM Accuracy   +/-1/10th RPM
  Inner Standard Rear Axle Width   23 IN / 58.4 CM   Outer Standard Rear Axle Width   61 IN / 155 CM
  Inner IXW Rear Axle Width   35 IN / 89 CM   Outer IXW Rear Axle Width   73 IN / 185.4 CM

  *Extended Carriage is Optional

Shop Requirements for Dynamometer

  • 120 Volt, 15 Amp, Single Phase
  • Requires 5CFM Air Compressor
  • PC Running Windows 7 or higher (Not Included)

Forklift Requirements

  • 2500lb Forklift with 6’ forks